Browse Categories
Browse by Manufacturer
Search

Mailing Lists

Walkera Devo 7 Setup Instruction

<< Previous in SPECIAL PURCHASES Next in SPECIAL PURCHASES >>
unavailable
Price: Click on "More Info" tab below for instruction
Out of stock
Part Number: Walkera Devo 7 Setup Instruction

DEVO 7 SETUP GUIDE

Setup for the RX2625H Receiver and the Devo 7 Transmitter. These settings should also work for the Devo 6 and Devo 8. Walkera Genius CP Helicopter.  Compliments of Tom Z .

* Intermediate to Advanced Settings
** Beginner Settings


**These are settings Tried. These are good starting points.
Some people use these settings as they are and others change them to meet there needs
Everyone has their own preference of settings so adjust and tweak my settings to meet your needs.**


This setup will give you 8-9* +/- pitch.
If you want more or less pitch turn up or down the pitch travel.
DO NOT set Rudder travel adjustment more than 100%. The tail will blow out
hard with any setting over 100%.

These are the settings used.
With these settings there is no change at all in RPM or pitch switching between modes. Normal, ST-1, and ST-2.
The heli won't rise or drop switching between modes.

Copy a model in the Devo 7:
At the default screen Press ENT, select MODEL on the top - Press ENT, select COPY - Press ENT, for SOURCE select select GENIS - Press ENT, for DEST select MOD 2 - Press ENT.


Intermediate to Advanced Settings

See picture below for the RX factory pot settings.

Verify the settings after you are done before you fly the Genius CP.

SWASH - 1-NRM

STMOD - MODE2 if you want the throttle on the left stick

REVERS - None, all normal

TRVAD - Pitch L & H = 65% to 70%

SUBTR - ALL 0.0%

DREXP - Set D/R and EXPO to your personal needs/preference. Here is what I use.


ELEV D/R 80% EXP +30% > Switch position 1
ELEV D/R 100% EXP +30% > Switch position 0

AILE D/R - 80%, EXP +30% > Switch position 1
AILE D/R - 100%, EXP +30% > Switch position 0

RUDD D/R - 100%, EXP -2% > Switch position 0 & 1

THHLD - STATE - ACT
POSIT - 0.0%

Set throttle trim to center!

It looks like Genius has firmware to run like this.


GYRO - MODE- AUTO

Set as high as you can go without getting tail wag. If you get tail wag with these numbers lower them
all equally EX: 78.0%, 78.0%, 78.0%

NORM - 82.0%

ST 1 - 82.0%

ST 2 - 82.0%

THHLD - This doesn't function on the Genius. Leave it where it is set to.


THCRV

To be able to set a value for a Throttle Curve you need to change STATE - INH to ACT


MODE - NORM

Set EXP to OFF

SRVHD - It appears this stops the servos or throttle on the helicopter from moving while you are in the program menu. When you exit they function again.
Selected YES then pressed ENT. If you want to work with the values and have throttle and servos working select NO then press ENT for SRVHD.

PL = 0.0%

P1 = INH

P2 - INH

PM = 100.0%

P3 = INH

P4 = INH

PH = 100.0%


MODE - ST-1

Set EXP to OFF

PL = 100.0%

P1 = INH

P2 = INH

PM = 100.0%

P3 = INH

P4 = INH

PH = 100.0%


MODE - ST-2

Set EXP to OFF


PL = 100.0%

P1 = INH

P2 = INH

PM = 100.0%

P3 = INH

P4 = INH

PH = 100.0%


PTCRV

To be able to set a value for a Picth Curve you need to change STATE - INH to ACT

MODE - NORM

Set EXP to OFF

SRVHD - It appears this stops the servos or throttle on the helicopter from moving while you are in the program menu. When you exit they function again.
Selected YES then pressed ENT. If you want to work with the values and have throttle and servos working select NO then press ENT for SRVHD.

PL = -35%

P1 = INH

P2 = INH

PM = 0%

P3 = INH

P4 = INH

PH = +100%


MODE - ST-1

Set EXP to OFF


PL = -100%

P1 = INH

P2 = INH

PM = 0%

P3 = INH

P4 = INH

PH = +100%


MODE - ST-2

Set EXP to OFF

PL = -100%

P1 = INH

P2 = INH

PM = 0%

P3 = INH

P4 = INH

PH = +100%

MODE - THHLD

Set EXP to OFF


PL = -100%

P1 = INH

P2 = INH

PM = 0%

P3 = INH

P4 = INH

PH = +100%

----------------------------------------------------------------------------------------------------------------------------------


Beginner Settings


See picture below for the RX factory pot settings.

Note: With these beginner settings there will be a height change when you switch back and fourth between Normal and Stunt modes.
The throttle curves have been tamed down for beginners. The pitch travel has also been tamed down for beginners. Normal mode will give you about 2-3* negative pitch.
More EXPO has been added and more D/R is used.

Verify the settings after you are done before you fly the Genius CP.



SWASH - 1-NRM

STMOD - MODE2 if you want the throttle on the left stick

REVERS - None, all normal

TRVAD - Pitch L & H = 60%

SUBTR - ALL 0.0%

DREXP - Set D/R and EXPO to your personal needs/preference. Here is what I use.


ELEV D/R 70% EXP +35% > Switch position 1
ELEV D/R 100% EXP +35% > Switch position 0

AILE D/R - 70%, EXP +35% > Switch position 1
AILE D/R - 100%, EXP +35% > Switch position 0

RUDD D/R - 100%, EXP +25% > Switch position 0 & 1



THHLD - STATE - ACT
POSIT - 0.0%

Set throttle trim to center!

It looks like Genius has firmware to run like this.

Read this post:

http://www.rcgroups.com/forums/showthread.php?t=1510032


GYRO - MODE- AUTO

Set as high as you can go without getting tail wag. If you get tail wag with these numbers lower them
all equally EX: 78.0%, 78.0%, 78.0%


NORM - 82.0%

ST 1 - 82.0%

ST 2 - 82.0%

THHLD - This doesn't function on the Genius. Leave it where it is set to.



THCRV

To be able to set a value for a Throttle Curve you need to change STATE - INH to ACT



MODE - NORM

Set EXP to OFF

SRVHD - It appears this stops the servos or throttle on the helicopter from moving while you are in the program menu. When you exit they function again.
Selected YES then pressed ENT. If you want to work with the values and have throttle and servos working select NO then press ENT for SRVHD.


PL = 0.0%

P1 = INH

P2 - INH

PM = INH

P3 = INH

P4 = INH

PH = 100.0%



MODE - ST-1

Set EXP to OFF


PL = 100.0%

P1 = INH

P2 = INH

PM = 80.0%

P3 = INH

P4 = INH

PH = 100.0%


MODE - ST-2

Set EXP to OFF


PL = 100.0%

P1 = INH

P2 = INH

PM = 100.0%

P3 = INH

P4 = INH

PH = 100.0%


PTCRV

To be able to set a value for a Picth Curve you need to change STATE - INH to ACT


MODE - NORM

Set EXP to OFF

SRVHD - It appears this stops the servos or throttle on the helicopter from moving while you are in the program menu. When you exit they function again.
Selected YES then pressed ENT. If you want to work with the values and have throttle and servos working select NO then press ENT for SRVHD.


PL = -35%

P1 = INH

P2 = INH

PM = 0%

P3 = INH

P4 = INH

PH = +100%


MODE - ST-1

Set EXP to OFF


PL = -100%

P1 = INH

P2 = INH

PM = 0%

P3 = INH

P4 = INH

PH = +100%


MODE - ST-2

Set EXP to OFF


PL = -100%

P1 = INH

P2 = INH

PM = 0%

P3 = INH

P4 = INH

PH = +100%


MODE - THHLD

Set EXP to OFF


PL = -100%

P1 = INH

P2 = INH

PM = 0%

P3 = INH

P4 = INH

PH = +100%
 
 
End of guide