Walkera 4#6S 3-Axis Hot Rod Helicopter RTF: 31714 BL Main, WK-2603 TX, CNC Head, Shaft Drive Tail, Extra Blades & Transmission Gear Set
Price: $245.95 Discontinued and replaced by M120-Bell
Out of stock
Part Number: PW-4#6S-31714+2603++
UPGRADED WK2603 TRANSMITTER FEATURES & ADVANTAGE
* Compatible to both FP(4) & CP(6) Channel Helicopters so you don't have to purchase another transmitter when you purchase a CP helicopter
* Select adjustments and switches listed below may be applicable to FP or CP helicopters.
* Pitch & Pitch Servo Travel Rate Adjustments
* Gyro Sensitivity & Rudder Mixing Adjustments
* Dual Servo Travel Rate Switch (ELEV/AILE/RUDD)
* Throttle Limited Height Switch (Throttle Curve Limits)
Normal & Stunt Flight Mode Switch
3 Axis gyro. Newest Hot Rod 4#6S with upgraded 31714 motor. Extremely stable to hover for the beginners and agile for intermediate to advanced pilots.
Walkera 4#6s 3 axis gyro Ready to Fly Helicopter with WK-2603 2.4gHz Transmitter
This is the first batch of 4#6S from Walkera with the original 4#6 skid and tail fins. The 3 axis receiver was installed on this heli and tested by Walkera.
Fix pitch graceful flight and stability !
Upgraded with Turbo Ace 31714 Power House Brushless motor
The Turbo Ace Power House 31714 inrunner motor installed. Helicopter is balanced and tunned to the upgraded motor. The 31714 is a direct drop in plug-and-play inrunner motor for the 4#6/4G6. It generates an additional 400 RPM from stock motor both running at 100% throttle. It is 3mm taller than stock, height is at 25mm verses stock at 22mm. When flying with stock radio setup, no adjustment is needed. Throttle curve can be increased to 100% and the motor still runs much cooler than Walkera stock inrunner motor. This motor totally eliminates the motor burn out problem found on the stock 4G6 and its does not require soldering like the outrunners. The motor needs the stock 10A Walkera ESC to properly fuel its amperage requirement, XP7A-2 rated at 7A will not be adequate to properly power this motor. The motor runs extremely efficient with lower temperature and achieve the same flight time as the Walkera stock. It does not need a direct soldered connection from the motor to the Walkera ESC, just tighten the screws and plug it in and you are ready for the extreme maneuvers of your time.
Motor type: Inrunner
Operating temperature: Normal flight 110 degrees vs. 130 degrees on stock Walkera BL motor. Full 3D flight 129 degrees vs. over 150 degrees for stock Walkera motor.
Weight: including wires- without connector: 12.9g. Weight: including wires- with connector: 13.3g
ESC Requirement and Compatibility: Requires minimum of 8A. It is fully compatible with the Walker ESC without any cogging issues
Pinion: Walker compatible 14 teeth pinion fully installed and balanced
Motor screws: Not included but compatible with the Walkera stock motor screws
Brand New 4#6
4#6 has comprehensive improvements in all the performance, stability, controllability and flight time over the 4G6. It is suitable for various hobbyists, especially for beginners/intermediates who have no desire to fly collective.
Swashplate Control System
Compact swashplate control system with Bell-Hiller mixing structure offers much more stable flight and meets various hobbyist's requirements for leisure and fun flights.
Brushless Power System
Powered by low-voltage-but-high-torque brushless motor and 3.7V 600mAh high performance Li-Po battery, supplies vigorous and lasting flights.
Highly Effective Shaft Transmission System
The use of highly effective shaft transmission system dramatically reduces extra loss from drive system and features prompter reaction and smarter operation.
AVCS Head Lock System
Perfect combination of built-in gyro, brand new AVCS head-locking technology and control system assures more accurate flight operation.
The creative usage of 3.7V low-voltage drive system with 2.4GHz spectrum technology annotates the philosophy of friendly environment and safety. Either charging at home or flying outdoors is highly safe. Auto protection structure can automatically stop all mechanism from spinning when the main blades impinge and reduce loss to minimum.
Longer Flight Life
4#6 optimizes both the mechanical structure and power system. The flight time of one cycle will be up to 10 minutes powered by 3.7V 600mAh Li-Po battery.
Transmitter: WK-2603 2.4.GHz
Receiver: RX2433 with Built-in 3 Axis Gyro
Brushless Motor: Upgraded Turbo Ace 31714
Brushless Speed Controller: WK-WST-10A-L
Gyro: Built-in AVCS
Battery: 3.7V 600mAh Li-Po (Charger Included)
Weight: 82g (Battery included)
Overall Length: 290mm
Main Rotor Dia: 258mm
Tail Rotor Dia: 76mm