|
|
Price: Was $38.95 now on sale $34.95
Includes 4 items. This kit is for 4G3, Novus CP only. It is not for 4#3B which needs a low tail fin, arriving early next week. Order other parts at no additional shipping charge. Consider purchasing the upgraded 2.9g BL motor w/ more power, 2 bearings.
|
|
|
Price: Was $38.95 now on sale $34.95
Includes 4 items. This kit is in stock for 4#3B/A only. It's not for 4G3 which needs a high tail fin. Remember to order other parts at no additional shipping charge. Ready to turn your 4#3B to hot rod? Click on MORE INFO above for addional BL main upgrade
|
|
|
|
|
|
|
|
Price: $15.95 Replaced by HM-4#3B-Z-37-40 Set
HM-4#3B-Z-37 has been replaced by the fully tested & assembled HM-4#3B-Z-37-40 motor/holder set. If you are doing a BL tail upgrade on a 4#3B/A or Novus FP, make sure you look for the Brushless 2g or 2.9g Tail Kit to get all the parts that are needed.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This is a genuine original Flea made in Germany by Nano manufacturer. Buyer beware! There are many Flea copies from China with out-dated fireware and inferior hardware parts that are not properly programmed or setup to handle the main and the tail motors.
|
Parts list to convert 4#3, 4#3A, 4#3B, 5G6 to brushless main and brushless tail. No technical support for this conversion is available and no liability is assumed from this recommended parts list.
|
No technical support is available when you do this conversion. Go to
http://www.rcgroups.com/forums/showthread.php?t=830186 for additional help. We do not assume any liability for the acurracy and the result of this diagram.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The least expensive way to convert Walkera 4#3B & 4G3 to brushless. It uses your exiting RX2406/RX2605/RX2400 receiver to convert to brushless main. It's a plug and play. It is also programmable Ebay ESC w/converter.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This is a 3 wire set for the brushless tail setup (30AWG). Note that most 30AWG wires will have a hard time fitting through the tail boom. This set of wires has extremely thin coating and will easily fit inside the hollow boom. They are appx 8 inches in l
|
|
|
|
|
|
Extended custom tail boom for the Walkera 4#3,4#3A,4#3B & Heli-Max Novus FP tail is 1/4 inch longer than 4#3B's HM-4#3B-Z-17 & Heli-Max's tail boom & 1/2 inch longer than the 4#3 stock boom and give the tail extra authority.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Price is for ten pairs ( 20 connectors). These polarized micro deans connectors offers many benefits
1. Polarity can't be reversed
2. Pins are spring tensioned for better contact
3. Connector with ridge to allow dislodging without pulling the wires
|
This programmer is for the Ebay 7A ESC only. Programmers are not compatible to other manufacturer's ESC.
|
|
|
|
|
This is a single channel converter made by the famous TheSteve. Comparable converter sells for $39. It converts the signal from the 4in1 Rx to PPM so you can use a brushless main motor.
|
|
|
|
Price: Turbo Ace 81016 Brushless Motor has been discontinued and it has been replaced by the more powerful 91416
Turbo Ace 81016 Brushless Motor has been discontinued and it has been replaced by the more powerful 91416.
|
|
|