This unit charges 2-cell & 3-cell batteries and includes a charging cable adapter to balance charge three 1-cell Walkera batteries simultaneously. Other adapters will not provide a balanced charge on multiple 1-cell batteries. Batteries are not included.

This balance charging cable adapter is used on a 3-cell charger (HM-CB180-Z-32 or B6 Charger - not included) to balance & charge 3 separate 1-cell batteries simultaneously. Other adapters will not provide a balanced charge on multiple 1-cell batteries.

This rugged Dual Turbo Ace Carrying Case provides ultimate protection for one V120D03/4G3 heli + one CB100/4#3B heli + Tx. Unlike typical aluminum cases, the Turbo Ace case is merticulously crafted from high gauge aluminum w/ a heavy duty handle.

This kit requires that you already have the "A" or "B" version receiver such as the RX2605A for the 4G3 & the RX2406A or RX2406B for the 4#3B.

This is a brushless converter with no soldering required for easy Plug-N-Play. It is extremely easy to install and can convert most brush receiver signal to brushless and it will work and plug into most brushless ESC.

Hot Rod Kit HP06 with 16T pinion BL motors, feather weight tail holder, exclusive motor clamp, Walkera tail ESC, wire set, manual & no tail rotor. This custom kit provides exceptional performance for 4#3B & Novus FP and it's wind tolerant

Weighing at 0.5g, the tail C-shape Carbon Stand/Holder + red tail boom CNC Metal Bracket fits the 2.5g (Turbo Ace 25700) & 2.9g (Turbo Ace 29701) upgrade for V100D01, 4#3B, CB100 & Novus FP* round tail booms. Tail rotor and motor are not included.

The Turbo Ace 91416 Brushless is the ultimate upgrade for your Walkera 4#3B, CB100 and Novus FP. It offers 20% more power than the Walkera 003 stock brushless. If you are upgrading from a brush motor you will need the CE700 or CE701 with your 91416.

You can effortlessly prolong battery life by frequently checking its voltage. Measuring 1-cell for Walkera/Novus and 3-6 cell for Trex450/600 helis, this one step plug & test meter is accurate and much easier to use than most cumbersome voltage meters.

Turbo Ace 81016 Brushless Motor has been discontinued and it has been replaced by the more powerful 91416.

500mAh battery & high discharge rate of 20C (Walkera battery is 400mAh & 12C) offers extended flight & excellent performance. Avoid using longer 600-900mAh batteries on micros because they are too heavy & the center of gravity is too far towards the tail.

Turbo Ace Super Capacity 650-700mAh Battery, designed to fit the Walkera 4G3/6/S, 4#6/S/BELL, CB100 & the V120 Series, will extend your flight time. Higher 20C high output increases power for more extreme maneuvers in both sport flying and 3D flight.

Manufactured by the same Linear battery factory, the 650mAh is now available using the same process and technology as the 400mAh Linear battery. It provides the greatest CG adjustment (1.2 inch) ever possible for the 4G6/4#6/V120D02/ Novus 125.

This is a special edition XP-7A-2 programmable ESC made to compatibility spec to both the outrunners/ inrunners w/Anti-cog outrunner firmware. Plug & play w/ Walkera connectors. It is ideal for upgrading to the lighter outrunner motors.

Customized to fit on Walkera transmitters, this Xtreme neck strap stabilizer bracket realigns the Tx to an optimum operating and viewing angle to ease arm, wrist & hand strain associated with holding and controlling the transmitter sticks simultaneously.

It's a hard to find the right kind of Thread Locking Adhesive that works and dries quick. Worse yet, certain thread locks are hard to dry.

This complete set includes magnetic base, protective metal case and micro blade balancer attachment to balance main blades for micro and super micro helicopoter. Compatible for models from Walkera, E-flite, Align T-Rex 100, Novus, Nine Eagle and etc.

HM-4#3B-Z-33, HM-4#3B-Z-34, HM-4#3B-Z-35 & HM-4#3B-41

This stock Walkera 2g brushless motor comes fully assembled and tested on the motor holder/stand (included). All you have to do is mount it on the tail boom and solder the wires back and you are done. Use the existing rubber grommet which is not included.

Two of the same phillips screwdrivers for the micro Walkera helicopters size 000- Spindle handle, magnetic and hardened tip. Improved optimum tip angel for a better fit on micro screws. The choice Phillips #000 screwdriver for Wow Hobbies technicians.

Weighing in at a mere 2.5g, this is the lightest dual-bearing brushless tail motor that you can glue-mount to the C-shaped carbon tail stand (not included). The stock brushless 2g motor has no bearings & will ware out prematurely.

This is the "glue-on-version". For the better and more secure "clip-on-version" look for the same item for $29.95. The current consensus is to convert Walkera brush and 2g brushless to the stronger 2.9g brushless tail motor with durable dual bearing.

The Turbo Ace 61316 (HP06) has been replaced by the 51416 BL Outrunner. The 51416's lighter design is more suited for micros and the updated speed eliminate the need to trim blades. So please look for listings that includes the 51416 instead of the 61316.

Modified Walkera HM-4G3-Z-39160 & 2.9g BL motors, feather weight tail holder, exclusive motor clip, Walkera tail ESC, wire set, manual: Optimum power on both the main and tail motors provides exceptional acceleration and a solid tail hold. No tail rotor.

These are premium extra durable blades for Walkera micro helicopters. Although blade dimensions are the same for Walkera CB100, 4#3A, 4#3B, V100D01 & Novus FP, the blue/black/white color stripes matches best with the Walkera CB100.

HM-4#3B-Z-(34&39) Combo wires set & Main ESC or Electronic Speed Controller (= HM-4G3-Z-40) for 4#3A, 4#3B, V100D01 & Novus FP is used in conjunction with a brushless main motor. For brushless tail motor please use the Tail ESC (HM-4#3B-Z-38).

Main Rotor Blades for the Walkera 4#3B/A, V100D01, CB100 & Novus FP are made of resilient zero memory plastic to maximize form retention. To prevent stripping, please do not over tighten the miniature screws.

HM-4#3B-Z-02: Flybar Paddles for Walkera 4#3B, Novus FP, 4#3A is slightly larger than the ones for 4#3 & improves stability on all 4 helicopters. Operational Tip: Make sure the paddles are adjusted to horizontal position before each flight.

HM-4#3B-Z-06: This light weight Steel Balance Flybar Assembly is also available as part of the Complete CNC Metal Head Set for the Walkera 4#3B/A & Helimax Novus FP.

HM-4#3B-Z-08: Servo Linkage Set for Walkera 4#3A, 4#3B & Heli-Max Novus FP helicopters. All Wow Hobbies helicopter spare parts are made by Walkera, the original factory for the 4#3A, 4#3B & Novus FP.

HM-4#3B-Z-09: CNC Metal Rotor Head Assembly with Main Shaft for Walkera 4#3B, 4#3A & Helimax Novus FP. This assembly is also available as part of the Complete CNC Metal Head Set for 4#3B. CNC components enhances handling & responsiveness.

HM-4#3B-Z-10: CNC Metal Swashplate, one of the initial advances by Walkera, markedly improved performance on the 4#3B which is later adopted for the Heli-Max Novus FP. This is one of many structual improvements that was key to 4#3B's success.

HM-4#3B-Z-15: Servo Holder Frame Mount is designed to secure servos for the 4#3A, 4#3B & Novus FP helicopters.

HM-4#3B-Z-16: Tail Holder Motor Mount for 4#3, 4#3A, 4#3B & Novus FP. This the holder for a standard brush tail motor. If you are upgrading to brushless tail motor you will need a different motor holder specifically for brushless motors.

HM-4#3B-Z-17: With minimal weight and maximum structual rigidity, this carbon Tail Boom for Walkera 4#3, 4#3A, 4#3B & Heli-Max Novus FP is 1/4inch longer which offers better tail authority than the old standard 4#3 boom.

Extended custom tail boom for the Walkera 4#3,4#3A,4#3B & Heli-Max Novus FP tail is 1/4 inch longer than 4#3B's HM-4#3B-Z-17 & Heli-Max's tail boom & 1/2 inch longer than the 4#3 stock boom and give the tail extra authority.

HM-4#3B-Z-23: If properly maintained, these original Walkera Ball Bearing Set for your 4#3A, 4#3B & Novus FP will increase fuel effeciency and prolong flight & limit prematured wear. Special Tip: Keep them away from moisture, dust & sand.

HM-4#3B-Z-24: It's a good idea to keep an extra set of screws to maintain your 4#3B, 4#3A & Novus FP. Miniature sized screws are easily stripped so a fresh set of screws every now and then prevents damage to other more expensive components.

HM-4#3B-Z-25 (HMXE2023)*: These original Walkera Digital 3G Nano Servos for 4#3A, 4#3B & Novus FP are some of the most advanced micro electronic mechanical devices on board. Features includes exceptional reaction time & digital precision.

HM-4#3B-Z-26: These are original Walkera Main Drive Motor for 4#3A, 4#3B & Novus FP at a super low price. Under a different item, we also have a lot of 10 motors for those who want to stock up.

HM-4#3B-Z-33. This is the standard Walkera Brushless Motor with 12T pinion for 4#3A/B/Q, CB100, V100D01, 4G3, Novus FP/CP. Before you buy this motor, check out the rugged Turbo Ace 91416 (under the same category) which is lighter and a lot more powerful.

HM-4#3B-Z-34 (HMXM3005)* Main ESC or Electronic Speed Controller for the Main Motor which is different than the ESC for the Tail Motor. For brushless tail motor please use the Tail ESC (HM-4#3B-Z-38).

HM-4#3B-Z-35: This is the newest version of a brush tail motor with higher performance to match with an upgraded brushless main motor. If you want a brushless tail motor you will need to look for a Brushless Tail Kit instead.

This a new replacement 2g tail motor which will fit with your stock Walkera brushless tail holder/stand. Wow also have 2.5g and 2.9g brushless tail motor options with dual bearings and custom carbon fiber tail holder/stand for more power and durability.

HM-4#3B-Z-41 Brushless RX2406B receiver for Walkera 4#3A, 4#3B & Heli-Max Novus FP. It's the new & improved receiver that makes calculated adjustments to stabilize handing and it's an updated version of the Walkera RX2406A or Helimax RX2400BL.

500mAh batteries weight little less than 600mAh batteries giving you a slighter lighter feel.

Center hole of this 14T pinion fits the 1.5mm shaft of the Walkera BL main motor, Feigao 12mmx20mm main motor, Losi 10,250kv or any motor with 1.5mm shaft. The pitch of this pinion matches the 4#3A, 4#3B, 4#3Q , 4G3, Novus FP & CP Main Gears.

HM-4G3-Z-31: Charger is shared between all micro 1s Walkera and Heli-Max Helicopter Models. The charger will automatically shut off upon charge completion and the LED indicator will turn from red to green. Charges any 1 cell Lipo 50 mAh to 1000 mAh.

HM-4G3-Z-39 (HM-4#3B-Z-33) Walkera BL Main Motor, WK-WS-12-003, 12T. If you are upgrading the 4G3, 4#6/S/BELL, V120D01/03, Novus CP/FP/125 FP please also consider the far superior & lighter Turbo Ace 71316 with rave reviews on its extraordinary power.

This Walkera brushless motor is custom fitted with a 16 teeth pinion for more powerful 3D on Walkera 4G6, 4G3 & Novus CP. You can also use this powerful option on a 4#3B, CB100, Novus FP in combination with a brushless tail motor.

HM-4G3-Z-40 (HM-4#6-Z-33) (HMXM3005)* Main Brushless Electronic Speed Controller for 4G3 & Novus CP is the same as HM-4#3B-Z-34 for 4#3B/A. This ESC is used only with a brushless main motor. For brushless tail motor please use a tail ESC (HM-4G3-Z-43).

This yellow/white/black tail rotor is usually used on the Walkera CB100, but it's the same as the 4#3B & V100D01 rotor except the color is different. You can also use this rotor for the upgraded MCPX Tail which has a 120SR motor (Not for stock MCPX tail).

HM-CB100-Z-13 (HM-4#3B-Z-11): for CB100, 4#3B & V100D01. If we are out of one check out the other part because they are the same part.

For 4#3B, CB100 & V100D01

HM-CB100-Z-26-3PLUGS Brushless Main Electronic Speed Controller (ESC) is used only with a brushless main motor. For brushless tail motor please use a Brushless Tail ESC (HM-CB100-Z-27).

HM-CB100-Z-26 Main ESC (Electroic Speed Controller) is used in conjunction with a brushless main motor. For brushless tail motor please use the Tail ESC (HM-CB100-Z-27).

HM-CB100-Z-27 (HM-4#3B-Z-38, HM-4G3-Z-43) Walkera Tail ESC/Converter: This Electronic Speed Controller also makes quick brushless tail signal conversions that is not provided by the brushless RX2406A/B or RX2400BL receivers with only BL main signals.

Steel Flybar

Screws & Connector are included. Matching pinion is available at http://wowhobbies.com/11tpinion64pitch-1.aspx This motor must be powered by ESC with a minimum of 6.5A otherwise ESC can be damaged. Go to http://wowhobbies.com/sale1299xp-7aebayblesc-1.asp

These high performance rechargeable batteries are especially suited for 3D & outdoor endeavors. 600mAh & a high discharge rate of 20C (vs standard 12C) offer excellent peak performance & longer flight time than Walkera or Heli-Max Novus batteries.

4#3B-Z-42600 Battery (600mAh 20C 3.7V) for 4#3B,4G3, 4G6 & all Walkera 1-cell helicopters. It offers longer flight time than the stock Walkera and Heli-Max Novus 400mAh batteries for the Novus FP & CP (GPMP0408)* and fits into all 1cell battery cages.

Radio transmitter hands free neck strap. Total length 45 inches.

A shorter and thicker high Capacity 600mAh COMPACT Battery is designed for the Lama2-1, Novus CX and smaller micros. It offers longer flight time than the stock Walkera 400mAh and does not throw off the CG (Center of Gravity) like other 600mAh batteries

This 600mAh gives you more flight time than the stock Lama2-1 battery and it provides better CG for micro helicopters such as the Lama2-1, Novus CX, 4#3B, CB100 & V100D01 because it fit further inside the battery tray than longer "Standard Size" LiPo.

Pinions are available separately, see More Info for detail. Includes the 3-pin Walkera motor connector installed.