Solder-less plug and play version with 9T MCPX pinion installed. This version has been tested with the E-Flite Blade MCP X micro heli brushless conversion. It is also great of Walkera or other micro brushless setup. MCP X 9 teeth pinion installed.

This unit charges 2-cell & 3-cell batteries and includes a charging cable adapter to balance charge three 1-cell Walkera batteries simultaneously. Other adapters will not provide a balanced charge on multiple 1-cell batteries. Batteries are not included.

This balance charging cable adapter is used on a 3-cell charger (HM-CB180-Z-32 or B6 Charger - not included) to balance & charge 3 separate 1-cell batteries simultaneously. Other adapters will not provide a balanced charge on multiple 1-cell batteries.

This rugged Dual Turbo Ace Carrying Case provides ultimate protection for one V120D03/4G3 heli + one CB100/4#3B heli + Tx. Unlike typical aluminum cases, the Turbo Ace case is merticulously crafted from high gauge aluminum w/ a heavy duty handle.

This is a brushless converter with no soldering required for easy Plug-N-Play. It is extremely easy to install and can convert most brush receiver signal to brushless and it will work and plug into most brushless ESC.

Hot Rod Kit HP06 with 16T pinion BL motors, feather weight tail holder, exclusive motor clamp, Walkera tail ESC, wire set, manual & no tail rotor. This custom kit provides exceptional performance for 4#3B & Novus FP and it's wind tolerant

Weighing at 0.5g, the tail C-shape Carbon Stand/Holder + red tail boom CNC Metal Bracket fits the 2.5g (Turbo Ace 25700) & 2.9g (Turbo Ace 29701) upgrade for V100D01, 4#3B, CB100 & Novus FP* round tail booms. Tail rotor and motor are not included.

At 9.1g, this ultra light premium linear current battery features consistent 20C high output without parabolic degradation towards the latter part of the flight cycle. Reduced inertia is extremely beneficial for extreme 3D and accelerated sport flying.

You can effortlessly prolong battery life by frequently checking its voltage. Measuring 1-cell for Walkera/Novus and 3-6 cell for Trex450/600 helis, this one step plug & test meter is accurate and much easier to use than most cumbersome voltage meters.

Turbo Ace 81016 Brushless Motor has been discontinued and it has been replaced by the more powerful 91416.

500mAh battery & high discharge rate of 20C (Walkera battery is 400mAh & 12C) offers extended flight & excellent performance. Avoid using longer 600-900mAh batteries on micros because they are too heavy & the center of gravity is too far towards the tail.

This is a battery meter with built-in low voltage alarm can also be installed on board helicopters. At low voltages, a led will light up and the double buzzers will also sound a warning for pilots who are too far from the helicopter to prevent crashes.

Manufactured by the same Linear battery factory, the 650mAh is now available using the same process and technology as the 400mAh Linear battery. It provides the greatest CG adjustment (1.2 inch) ever possible for the 4G6/4#6/V120D02/ Novus 125.

This is a special edition XP-7A-2 programmable ESC made to compatibility spec to both the outrunners/ inrunners w/Anti-cog outrunner firmware. Plug & play w/ Walkera connectors. It is ideal for upgrading to the lighter outrunner motors.

This balance charging cable adapter is used on a 3-cell charger (HM-CB180-Z-32 or B6 Charger - not included) to balance & charge 3 separate 1-cell batteries simultaneously. Other adapters will not provide a balanced charge on multiple 1-cell batteries.

It's a hard to find the right kind of Thread Locking Adhesive that works and dries quick. Worse yet, certain thread locks are hard to dry.

This complete set includes magnetic base, protective metal case and micro blade balancer attachment to balance main blades for micro and super micro helicopoter. Compatible for models from Walkera, E-flite, Align T-Rex 100, Novus, Nine Eagle and etc.

HM-4#3B-Z-33, HM-4#3B-Z-34, HM-4#3B-Z-35 & HM-4#3B-41

The least expensive way to convert Novus FP, Walkera 4#3B & 4G3 to brushless. It uses your exiting RX2400/RX2406/RX2605 receiver to convert to brushless main. No soldering is required. CE701is a converter with a programmable Ebay ESC. Rx is not included.

Weighing in at a mere 2.5g, this is the lightest dual-bearing brushless tail motor that you can glue-mount to the C-shaped carbon tail stand (not included). The stock brushless 2g motor has no bearings & will ware out prematurely.

This is the "glue-on-version". For the better and more secure "clip-on-version" look for the same item for $29.95. The current consensus is to convert Walkera brush and 2g brushless to the stronger 2.9g brushless tail motor with durable dual bearing.

Stock brush tail motors have limited power due to lower thrust & RPM and stock 2g brushless has no bearing which wears out easily. This is the only secured "Clip-On" (Not the "Glue-On") 2.9g double bearing version used to upgrade Walkera's tail motors.

Tail kit includes 2.9g Turbo Ace 29700 brushless tail motor, C-shape holder w/ carbon stand & RED CNC tail boom clamp- Only weights 0.5g , brushless wire set and exclusive motor-locking clamp. Holder fits 4#3B or Novus FP boom. Tail rotor not included.

These are premium extra durable blades for Walkera micro helicopters. Although blade dimensions are the same for Walkera CB100, 4#3A, 4#3B, V100D01 & Novus FP, the blue/black/white color stripes matches best with the Walkera CB100.

These are premium extra durable blades for Walkera micro helicopters. Although blade dimensions are the same for Walkera CB100, 4#3A, 4#3B, V100D01 & Novus FP, the red/black/white color stripes matches best with the Walkera 4#3A, 4#3B, V100D01 & Novus FP.

These are premium extra durable blades for Walkera micro helicopters. Although blade dimensions are the same for Walkera CB100, 4#3A, 4#3B, V100D01 & Novus FP, the blue/black/white color stripes matches best with the Walkera CB100.

These are premium extra durable blades for Walkera micro helicopters. Although blade dimensions are the same for Walkera CB100, 4#3A, 4#3B, V100D01 & Novus FP, the red/black/white color stripes matches best with the Walkera 4#3A, 4#3B, V100D01 & Novus FP.

HM-4#3B-Z-02: Flybar Paddles for Walkera 4#3B, Novus FP, 4#3A is slightly larger than the ones for 4#3 & improves stability on all 4 helicopters. Operational Tip: Make sure the paddles are adjusted to horizontal position before each flight.

Walkera HM-4#3B-Z-03 Tail Rotor Blade for 4#3B & 4#3A is the same as Heli-Max Tail Rotor Blade for Novus FP with only minor cosmetic differences. This is a very commonly used replacement part.

HM-4#3B-Z-05: CNC Metal Blade Holder/Grip Set is a for 4#3B & Novus FP but can also be used to upgrade your 4#3A plastic to metal holders. Repair Note: When the blades strike a surface, their holders can also be bent or damaged occasionally.

HM-4#3B-Z-11 (HM-CB100-Z-13): The Skid Landing Gear is one of the most used spare part for repairs. Along with blades, this feather weight skid takes the brunt of most crashes. The good news is that the skid is one of the easiest parts to replace.

HM-4#3B-Z-12: Battery Frame/Tray for Walkera 4#3B, 4#3A & Helimax Novus FP is designed for original batteries but is also flexible enough to secure most 3rd party 12C-20C 400mAh-500mAh batteries with slightly thicker or longer dimensions.

HM-4#3B-Z-13: Made of high impact plastic, the Tail Rotor Gear is shared between several models of Walkera micro helicopters including the 4#3, 4#3A, 4#3B, 4#3Q & Novus FP.

HM-4#3B-Z-14: This is the standard Tail Knighthead/Skid for 4#3, 4#3A, 4#3B & Novus FP. As an alternative, you can make a couple of much stronger tail knight heads by ordering the following 2 parts listed under "More Info".

HM-4#3B-Z-20 (HM-CB100-Z-15): The Main Gear for 4#3B, 4#3A & Novus FP works in conjuction with the main motor & the main rotor assembly. Installation requires that you properly align the main motor pinion with the main gear to prevent premature ware.

HM-4#3B-Z-21: Canopy for 4#3A & 4#3B has the same specs as the Novus FP Canopy. The only difference is cosmetic so the two canopies are interchangeable. The canopy mounting rod is included as shown on the picture.

HM-4#3B-Z-22: Pre-assembled Tail Motor Wire for Walkera 4#3, 4#3A, 4#3B & Heli-Max Novus FP Helicopters.

HM-4#3B-Z-23: If properly maintained, these original Walkera Ball Bearing Set for your 4#3A, 4#3B & Novus FP will increase fuel effeciency and prolong flight & limit prematured wear. Special Tip: Keep them away from moisture, dust & sand.

See similar item on sale but rated at 20C instead of 12C with longer flight time for the same price per battery at http://wowhobbies.com/battery20cfor43-1.aspx

HM-4#3B-Z-29: Charger for all Walkera & Novus 1-cell helicopters. Chargers features convenient "plug in the wall outlet" with operation that will automatically shut-off when the battery is fully charged and the LED indicator turns from red to green.

HM-4#3B-Z-32 : The newest version Main Frame for Walkera 4#3A, 4#3B, V100D01 & Heli-Max Novus FP will fit with all Walkera brush & brushless motors plus many third party brushless motors such as the Turbo Ace 91416.

HM-4#3B-Z-33. This is the standard Walkera Brushless Motor with 12T pinion for 4#3A/B/Q, CB100, V100D01, 4G3, Novus FP/CP. Before you buy this motor, check out the rugged Turbo Ace 91416 (under the same category) which is lighter and a lot more powerful.

HM-4#3B-Z-38 (HM-CB100-Z-27, HM-4G3-Z-43) Walkera Tail ESC/Converter: This Electronic Speed Controller also makes quick brushless tail signal conversions that is not provided by the brushless RX2406A/B or RX2400BL receivers with only BL main signals.

HM-4#3B-Z-39: This is a pre-assembled Walkera Tail Motor Brushless Wire Set to make brushless tail conversions for 4#3, 4#3A, 4#3B & Novus FP helicopters as easy as 1-2-3. You should also check out the complete Brushless 2g and 2.9g Tail Kits.

HM-4#3B-Z-41 Brushless RX2406B receiver for Walkera 4#3A, 4#3B & Heli-Max Novus FP. It's the new & improved receiver that makes calculated adjustments to stabilize handing and it's an updated version of the Walkera RX2406A or Helimax RX2400BL.

500mAh batteries weight little less than 600mAh batteries giving you a slighter lighter feel.

HM-4G6-Z-37600 Battery: (3.7v, 600mAh, 15C) fits perfectly in Walkera & Novus 1- cell helis & offers longer flight time than the stock 400-500mAh batteries. Please click on "More Info" to see the link for the ultimate "650mAh" high capacity battery.

HM-4G3-Z-24 : Tail Motor Wire for 4G3, 4#3A, 4#3B, Novus CP & FP. Custom lenght wire plus connector assembled for your convenience.

HM-4G3-Z-30:* Battery(3.7v 400mAh) for Walkera 4G3 & Novus CP. Please see the upgraded version rated at 20C (instead of 12C) with longer flight time on sale for the same price per battery at http://wowhobbies.com/battery20cfor43-1.asp

HM-4G3-Z-31: Charger is shared between all micro 1s Walkera and Heli-Max Helicopter Models. The charger will automatically shut off upon charge completion and the LED indicator will turn from red to green. Charges any 1 cell Lipo 50 mAh to 1000 mAh.

HM-4G6-Z-36 is the Main ESC that controls the main motor which is different than the Tail ESC.

Just a bit longer than the older 450mAh & 500mAh batteries, this original Walkera 600mAh 1-Cell battery still retains the same thickness and width so it will fit perfectly into the same battery cages as before. Dim: 40mm x 24.5mm x 8mm, Wt: 15.3g

These blades are used on the CB100, V100D01, 4#3B & Novus FP helicopters.

HM-CB100-Z-26-3PLUGS Brushless Main Electronic Speed Controller (ESC) is used only with a brushless main motor. For brushless tail motor please use a Brushless Tail ESC (HM-CB100-Z-27).

HM-CB100-Z-26 Main ESC (Electroic Speed Controller) is used in conjunction with a brushless main motor. For brushless tail motor please use the Tail ESC (HM-CB100-Z-27).

HM-CB100-Z-27 (HM-4#3B-Z-38, HM-4G3-Z-43) Walkera Tail ESC/Converter: This Electronic Speed Controller also makes quick brushless tail signal conversions that is not provided by the brushless RX2406A/B or RX2400BL receivers with only BL main signals.

Steel Flybar

Carbon Flybar

This is a brushless converter with no soldering required for easy Plug-N-Play. It is extremely easy to install and can convert most brush receiver signal to brushless and it will work and plug into most brushless ESC.

Center hole of this 16T pinion fits the 1.5mm shaft of the Walkera BL main motor, Feigao 12mmx20mm main motor, Losi 10,250kv or any motor with 1.5mm shaft. The pitch of this pinion matches the Walkera 4#3A, 4#3B, 4#3Q, 4G3, Novus FP & CP Main Gear.

The Walkera WK-2402 Transmitter is compatible with all Walkera and Novus 4-Channel 2.4gHz helicopters.

The Walkera WK-2403 is compatible with all Walkera and Novus 4 channel 2.4gHz helicopters.

Compatible to all the latest 3-Axis Walkera receivers such as RX2433, RX2435, RX2437S, RX2610S and Heli-Max Novus equivalents.... ETC.

Compatible to all the latest 3 axis Walkera & Heli-Max Novus receivers such as RX2433, RX2435, RX2437S, RX2610S & Heli-Max Novus equivalents.