B6 Balance Charger/Discharger with power supply (This item has been replaced by advanced CX-B601 charger.)

<< Previous in ACCESSORIES

Next in ACCESSORIES >>

Price: $69.95 This item has been replaced by more advanced charger CX-B601

Out of stock

Part Number: WWC-TE-B6

Manufacturer: WOW

Manufacturer Part No: WWC-TE-B6

Email this page to a friend

This item has been replaced by more advanced online firmware upgradable charger CX-B601.

Click on http://www.wowhobbies.com/b6balancechargerdischarger-1.aspx

Includes power supply ($29 value) normally not included with charger. Allows charging from 110v to 240v wall plug or 12v car battery.

This inteligent B6 charger keeps your battery in good condition for maximum battery cycles by setting your own charge current. The B6 charger will charge a Walkera 1 cell battery but you would need to purchase a adapter connector. Unlike the Walkera wall charger which charges a 600mAh battery at 1 amp, the B6 is able to be set to charge at the proper current therefore preserving the life cycle of the battery. The gang adapter that is available to hook up your Walkera 1 cell battery to the B6 is available here http://www.wowhobbies.com/jst2pinplugwith5xwalkeraplugs.aspx You can charge a few batteries at a time but we recommend charging only one battery at a time due to the lack of balancing with this gang adapter plug.

SIMPLE TO FOLLOW DIRECTION

Simple to operate, just make sure the balancing plug and the red Deans discharging plug of the battery are both plugged into the charger. If you only plug in the balancing lead you will see a message "CONNECTION BREAK". Select the battery type (NiCd/NiMh/Li-Po/Li-ion/Li-Fe/Pb), amperage and the charging voltage (number of cells for Lipos) then press and hold ENTER to start the charge. To set the charge rate, 500mAh battery should be charged at no more than 0.5A, 1000mAh battery no more than 1A, 2000mAh battery no more than 2A. Formular for the charge rate must be no more than 1A per 1,000mAh of battery capacity.

MG Power B6 Balance Charger and Discharger
Microprocessor Controlled High Performance- rapid charge for NiCd/NiMh/Li-Po/Li-ion/Li-Fe/Pb Batteries

Features:

Optimized Operating Firmware: MG Power B6 features AUTO function that set the feeding current during the process of charging or discharging. Especially for Lithium batteries, it can prevent the overcharging which may lead to an explosion due to the user's fault. It can disconnect the circuit automatically and alarm once detecting any malfunction. This device uses intelligent analog circuit to achieve maximum safety and minimizes charging errors. All the settings can be configured by users!
Internal Independent Lithium Battery Balancer: MG Power B6 employs an individual-cell-voltage balancer. It isn't necessary to connect an external balancer for balance charging
Balance Individual Cells Battery Discharging: During the process of discharging, MP Power B6 can monitor and balance each cell of the battery individually. Error message will be indicated and the process will be ended automatically if the voltage of any single one cell is abnormal
Adaptable to Various Type of Lithium Battery: MP Power B6 is adaptable to various types of lithium batteries, such as Li-ion, Li-PO and the new Li-Fe series of batteries
Fast and Storage Mode of Lithium Battery: Purposes to charge lithium battery varies, 'fast' charge reduce the duration of charging, 'store' function can control the final voltage of your battery, so as to store for a long time and protect useful time of the battery
Maximum Safety: Delta-peak sensitivity: The automatic charge termination program based on the principle of the Delta-peak voltage detection. When the battery's voltage exceeds the threshold, the process will be terminated automatically
Automatic Charging Current Limit: You can set up the upper limit of the charging current when charging your Ni-Cd or Ni-MH battery; it is useful for the Ni-MH battery of low impedance and capacity in the 'AUTO' charging mode
Capacity Limit: The charging capacity is always calculated as the charging current multiplied by time. If the charging capacity exceeds the limit, the process will be terminated automatically when you set the maximum value
Temperature Threshold*: The battery's internal chemical reaction will cause the temperature of the battery to rise. If the temperature limit is reached, the process will be terminated. *This function is available by connecting optional temperature probe, which is not included in our package
Processing Time Limit: You can also limit the maximum process time to avoid any possible defects
Input Power Monitoring: To protect the car battery used as DC input power from being damaged, its voltage keeps being monitored. If it drops below the lower limit, the process will be ended automatically
Data Store / Load: The maximum five batteries's data can be stored for user's convenience. You can keep the data pertaining to program setting of the battery of continuous charging or discharging. Users can call out these data at any time without any special program setting
Cyclic Charging / Discharging: 1 to 5 cyclic and continuous process of charge > discharge or discharge > charge is operable for battery refreshing and balancing to stimulate the battery's activity

Specification:

Operating voltage range: DC11.0 ~ 18.0 Volt / AC to DC adaptor (DC11.0 ~18.0V/5A)
Circuit power: Max. charge current 5A / Max. discharge current 1A
Charge current range: 0.1 ~ 5.0A
Discharge current range: 0.1 ~ 1.0A
Current drain for balancing Li-PO: 300mAh/cell
NiCd / NiMH battery cell count: 1 ~ 15cell
Li-ion / Polymer cell count: 1 ~ 6series
Pb battery voltage: 2V ~ 20V
Weight: 265g (Net weight)
Dimensions: 133.2 X 80.6 X 33mm

Package Includes:

MG Power B6 charger
Power supply which is required if you are charging from 110v outlet. It is normally not included with charger.
Charging cables for various batteries
Instruction manual